How Much Coil Does a Decoiler Leave at the Coil End?
A 1,250 mm coil of 2 mm steel holds about 512 metres of strip. Roughly 20 of those metres never reach the die.
They stay wrapped on the mandrel because the coil has lost the diameter that gave the mandrel something to grip, and they leave the plant as scrap on every single coil.
On 9.6 tonnes of steel that is 400 kg a coil, or a little over 4 percent. Multiply it by 900 coils a year and the arithmetic stops being academic.
Count the Turns You Cannot Feed
The geometry is simple.
Strip length on a coil is the annular area divided by the strip thickness. For a round coil that reduces to pi times the difference of the squares of the two diameters, over four times the thickness.
Put numbers in and the result is intuitive. A 1,250 mm outside diameter over a 508 mm bore at 2 mm thickness gives about 512 metres.
The same coil at 1 mm holds twice that, because the annulus is filled with thinner layers.
The limit is not the bore. It is the point where the remaining wraps can no longer resist the pull of the line.
Below roughly 540 to 620 mm outside diameter, depending on thickness and yield, the coil starts to collapse inward or slip against the mandrel segments.
Operators learn that limit by feel and stop a little early. The cost of stopping early is paid in strip, every coil, and it never appears on a scrap report because it is booked as coil yield.
That accounting habit is why the number stays invisible for years. Coil yield is reported as a percentage against the purchased weight, and a line running 96 percent looks healthy next to a target of 95.
Nobody asks which part of the missing 4 percent was process scrap and which part never left the mandrel.
They are different problems with different fixes, and one of them is solved by a hardware order rather than a training session.
Two more coils of context. A 610 mm bore coil carries less strip for the same outside diameter, so the remnant is a slightly larger share of a smaller coil.
And a coil wound loosely at the service centre runs out earlier than a tight one, because the wraps move before the diameter reaches the limit.

Worked Example on a 1,250 mm Coil
The table below uses one coil: 1,250 mm outside diameter, 508 mm bore, 1,200 mm wide, 2 mm CR4 at 7.85 kg per cubic decimetre. Only the diameter at which the operator stops changes.
| Diameter at stop | Strip left on the coil | Mass left | Share of the coil |
|---|---|---|---|
| 620 mm | 49.6 m | 934 kg | 9.7 percent |
| 600 mm | 40.0 m | 754 kg | 7.8 percent |
| 560 mm | 21.8 m | 411 kg | 4.3 percent |
| 540 mm | 13.2 m | 248 kg | 2.6 percent |
Two observations follow. First, the difference between a cautious operator and a confident one is worth 500 kg a coil.
Second, the last 40 mm of diameter carries almost a fifth of the total remnant, which is why the final metres are where the argument happens.
At USD 620 a tonne, the gap between stopping at 620 mm and stopping at 560 mm is USD 324 per coil. Across 900 coils that is USD 291,000 a year of strip that was already paid for.
Thickness changes the picture more than most buyers expect. The same 560 mm stop on 0.8 mm strip leaves under 9 metres, because the annulus holds two and a half times as many layers.
On 3 mm strip the same stop leaves about 33 metres and 1.1 tonnes, which is close to 11 percent of the coil. The heavier the gauge, the more the remnant behaves like a capital item rather than a rounding error.
Width does not enter the length calculation at all. It only scales the mass, so a 1,500 mm wide line leaves the same 21.8 metres but 30 percent more kilograms on the mandrel.
What Sets the Smallest Diameter You Can Run
Four hardware details decide how far down the coil can go before the line loses control of it.
Mandrel expansion range. A mandrel that opens from 450 to 530 mm grips a 508 mm bore across the whole run, but it has nothing to push against once the wraps loosen.
Segments with longer travel and a slight crown hold better at small diameters.
Hold-down or snubber arm. A powered arm pressing on the outside of the coil keeps the wraps tight as the diameter falls. Without one, the coil loosens and the strip starts to telescope sideways.
Brake or drive response. The torque needed to hold back tension falls with diameter, but the control has to follow it.
A brake set for a full coil will over-brake a small one and pull the wraps tight against the mandrel.
Coil car and peeler height. If the remnant has to be lifted off by hand, operators stop early to avoid the lift. A car that reaches the mandrel at 540 mm removes that incentive entirely.
Check the four items in that order before blaming the operator for stopping early. In most plants the machine has been asking for the early stop all along.
- Measure the mandrel at full collapse and compare it with the bore of the coils you actually buy.
- Run one coil to the point where the wraps move, with the hold-down fitted, and record the diameter.
- Confirm the brake follows the falling diameter rather than holding a fixed torque.
- Time the removal of a 540 mm remnant, because a two-minute lift is a two-minute reason to stop at 620.
Where the Saving Really Comes From
Four routes recover part of that 400 kg, and they are not equally cheap. The table puts the strip saved next to the constraint each one carries.
| Method | Strip recovered per coil | Where it costs you |
|---|---|---|
| Run down to 540 mm with a hold-down arm | 300 to 500 kg | Needs an operator willing to watch the last two minutes, and a coil break at the tail can mark the rolls |
| Weld the tail to the next coil | Nearly all of it | A welder, an accumulator and a weld seam that must survive every downstream operation |
| Return remnants to the service centre for credit | 60 to 80 percent of material value | Handling, floor space and a collection schedule that rarely matches production |
| Buy heavier coils less often | Nothing per coil, fewer coils | Crane capacity and floor loading, and a longer run between changes only helps if the schedule allows it |
For most plants the hold-down arm is the first move. It is a hardware addition rather than a process change, it does not touch the strip quality, and it pays back inside a year on a single high-volume coil size.

Tail welding is the bigger prize and the bigger commitment. It only makes sense when the line runs continuously for hours, because the weld has to be proven before it reaches the first forming station.
What the Arithmetic Ignores
The calculation is honest about geometry and silent about four things that decide the real number.
It assumes a round, tight coil.
A telescoped coil or one that has sat through a humid season will not run to 540 mm at all, because the wraps have already separated and the coil will collapse before the diameter gets there.
It ignores cross-welded tails. Service centres weld coil ends together, and that weld has to be cut out before it reaches the die. A cut-out of 300 mm on every coil removes most of what a hold-down arm saves.
It treats the remnant as a total loss. In practice a remnant has scrap value, so the net cost is the difference between material price and scrap price, which on CR4 is often 55 to 70 percent of the gross figure.
And it says nothing about the line downstream.
Running a coil to a smaller diameter means the last metres are stiffer and less flat, so the first parts after a fresh coil are not the only ones at risk of a tolerance excursion.
A decoiler and a plain uncoiler are sized by the same bore arithmetic, so the remnant figure applies to both. The difference is only in how the last wraps are held.
How much strip is left when a coil stops at 600 mm?
About 40 metres on a 1,250 mm by 2 mm coil, or 754 kg. That is 7.8 percent of a 9.6 tonne coil, and it is roughly double the remnant at 560 mm.
Does a hold-down arm pay back on 900 coils a year?
Yes, typically in 8 to 14 months. Recovering 350 kg a coil at USD 620 a tonne returns about USD 195,000 a year against an arm that costs a fraction of that.
At what thickness does the remnant share become negligible?
Below 0.6 mm the same geometry leaves under 1.5 percent, because the annulus holds many more layers. Above 3 mm it can exceed 12 percent and the arithmetic changes the buying decision.
Our coil line knowledge base takes the same four decisions in order: capacity, type, mandrel, control.
Mandrel expansion ranges and hold-down options by model are listed in the coil handling product index.
Where to go next
Remnant arithmetic is one input to the capacity and mandrel decision. The specification pillar takes the four decisions in order and shows where a smaller coil diameter changes the machine you should be buying.
Read the decoiler specification guide



