An Expert in Decoiler Feeder & Metal Coil Processing

Home / All / Buyer Guide / Which Warranty Terms Protect a Coil Line Buyer?

Which Warranty Terms Protect a Coil Line Buyer?

Nov 18,2026

A coil line warranty is worth exactly what its exclusions allow, and most buyers read the coverage sentence and skip the four pages behind it.

We sit on both sides of that conversation. FANTY has commissioned lines in more than 60 countries, and the claims that get paid are almost always the ones the buyer documented before the first coil went on.

What follows compares the three warranty structures sold today, then shows where each one quietly hands the risk back to you.

Machine pages in the coil line equipment index list what each build includes, which is a useful cross-check against the wording.

First Decide What the Clock Is Measuring

Every warranty has a start event, and that event is where more money is lost than in any coverage clause.

Four start points are in common use: bill of lading date, arrival at the destination port, mechanical completion, and sign-off after the acceptance run.

On a line shipped from Shenzhen to Rotterdam or Santos, the spread between the first and last of those is routinely four to six months.

The arithmetic is unforgiving. A 12-month term counted from the bill of lading on a March shipment expires in March of the following year.

If your line was installed in June and signed off in August, you have already spent five of those months waiting for a foundation to cure.

Ask for the term to run from commissioning sign-off, with a backstop such as 18 months from bill of lading so the clock cannot run forever on a machine sitting in a warehouse.

Write both dates into the contract. A single date invites a discussion at the worst possible moment, which is the week a gearbox fails.

Three Structures, Three Different Risks

Suppliers do not offer one warranty. They offer one of three, and each moves a different cost onto your side of the table.

Warranty structureWhat it actually pays forWhat it leaves with you
Parts only, 12 monthsReplacement components, ex-worksTechnician time, air freight, customs on the spare, and every hour of downtime
Parts and labour, 18 monthsComponents plus service hours on siteProduction loss, crane hire, and the argument over whether the failure was operational
Performance guaranteeAccuracy and speed commitments, with a penalty or price rebateThe cost of the acceptance test, and the burden of proving the test conditions were met
Buyer and engineer reviewing coil line warranty and contract documents at a machine

The third structure looks strongest on paper and is the hardest to enforce. It only bites if the test method, the material and the speed are all defined before signature.

A performance figure of ±0.05 mm means nothing if the guarantee does not say at what thickness, what width and what press speed it was measured.

Price the structures, not the months. Moving from parts-only to parts and labour typically adds 1.5 to 2 percent of machine value, which is cheap next to one gearbox swap.

Where the Exclusions Do the Real Work

Coverage paragraphs are written by marketing. Exclusion lists are written by people who have paid claims.

Read the second one first, and read it against the parts that actually fail on your line.

Consumables. Feed rolls, straightener rolls, brake linings, hydraulic seals and mandrel segments are usually excluded as wear items.

Those parts are also the majority of what a line consumes in its first three years, which makes the exclusion larger than the coverage.

Ask for a named consumables schedule with expected life in metres or strokes. A supplier who cannot produce one has not been asked before.

Undefined misuse. The phrase "operation outside specification" is the most common reason a claim dies.

If your material runs 0.1 mm over the quoted thickness, or your voltage swings 8 percent, that clause becomes the whole conversation.

Define the operating envelope in an annex: thickness range, width range, tensile range, power quality, ambient temperature. Then misuse has a boundary.

Consequential loss. No supplier in this industry covers lost production, and it is not worth fighting for.

Insure that exposure separately, or hold enough finished stock to ride out a week. A warranty is a parts argument, not a business interruption policy.

What Has to Be on File in the First 72 Hours

Claims are decided by records that either exist or do not. None of this takes long if it is done while the crew is still on site.

  • Unloading photographs, container condition and any shock or tilt indicator reading, taken before the crate is opened
  • Foundation and levelling record with the actual shim values, not the drawing tolerance
  • A power quality log covering voltage, phase imbalance and earth resistance at the machine terminals
  • The first-run parameter sheet, signed, with roll gaps, feed length and pilot release timing as set
  • Handover checklist with measured accuracy on your material, not on the test strip

Two hours of paperwork on handover day is the difference between a paid claim and a discount argument eighteen months later.

Photograph the serial plate as well. A claim that cannot be tied to a serial number is a claim the factory cannot process.

Four questions come up in nearly every contract review we sit through, so they are worth answering directly.

Does a 12-month warranty cover the feed rolls?

Usually not, and it should not. Rolls are a wear item with a defined life in metres. What you can negotiate is a first replacement set at cost, which on a 1,300 mm line saves roughly USD 3,000 to 6,000.

Can a warranty start 6 months after the bill of lading?

Yes, and it is a normal request on ocean freight. Expect the supplier to cap total exposure, typically at 18 months from shipment, so the term cannot run on an idle machine.

How much does a 24-month term cost over 12 months?

Budget 1.5 to 2.5 percent of machine value for the extra year when it includes labour. On a USD 180,000 line that is USD 2,700 to 4,500, against a single on-site service visit that can run USD 3,000 with travel.

What accuracy figure should a performance guarantee state?

Write it as a triple: ±0.05 mm at 200 SPM on 1.2 mm CR at 1,000 mm width. Any single number without thickness, width and speed is unenforceable, and both sides know it.

Claims That Get Paid and Claims That Stall

The difference between a claim settled in two weeks and one that drags into a second quarter is rarely technical.

Stage of the claimEvidence that decides itCost of getting it wrong
NotificationTimestamped message with serial number, photo and running hoursLate notice lets the supplier argue the fault was known and unreported
Root causePhotographs taken before dismantling, plus strip samples from the failed runOnce the part is off the machine, wear and fatigue look identical
Parts returnThe failed component itself, cleaned and tagged, not scrappedNo return, no credit, and the replacement is invoiced at list price
Labour recoveryService report with names, hours and tasks per technicianTwo or three days of your own maintenance time absorbed silently

Notice how little of that is about the machine. It is about whether you can prove a sequence of events.

What No Warranty Will Ever Cover

A warranty is a defect remedy. It is not a maintenance contract and not a performance insurance policy.

It cannot cover your production. A three-day stop on a line making 40,000 parts a day is a commercial loss, and no supplier in this market writes that cheque.

It cannot fix a wrong specification. If the line was bought for 1.2 mm and you later run 2.5 mm HSLA 420, the failures that follow are outside the envelope you signed.

It cannot survive skipped maintenance. Most contracts require lubrication and inspection records. Without them the supplier has a defensible exit.

It cannot make a performance figure transferable. A guarantee measured on 1.0 mm CR does not carry over to SUS304 at the same thickness, because springback and roll load both change.

Treat the document as a defined remedy with a defined boundary. Buyers who expect more end up negotiating instead of producing.

Turning Two Offers Into One Number

When two suppliers quote the same machine with different warranty wording, compare them on expected cost, not on months.

Purchasing team comparing coil line warranty offers and spare parts pricing

Take the parts that failed on your previous line in the last five years, price them at the quoted rates, and apply each warranty's exclusions.

The offer with the longer term but a wider consumables exclusion often comes out behind. That calculation takes an afternoon and settles the argument.

FANTY builds with 370 staff and 80-plus engineers, which matters here for one practical reason: a factory that designs its own roll stacks can name a wear life instead of guessing at one.

Ask both suppliers for that number in writing. It belongs in the same annex as the exclusion list.

Where to go next

Warranty wording only matters against a specification that was priced properly in the first place.

The cluster's cost pillar maps each specification line to the machine price and the local landing cost it creates, which is the right order to negotiate in.

Read the specification cost pillar

Follow us to Get Latest Updates

subscription