An Expert in Decoiler Feeder & Metal Coil Processing

Home / All / NC Servo Straightener Feeder Guide / What Changes When a 3-in-1 Switches Coil Width?

What Changes When a 3-in-1 Switches Coil Width?

Nov 16,2026

A width change looks like a coil swap and behaves like a setup. Thickness changes get planned, tooled and checked.

Width changes get made in twenty minutes by whoever is on the line, and then the first two hundred parts run with an edge guide set by eye.

On a 1,300 mm three-in-one machine running down from 1,200 mm to 420 mm strip, six settings move and one of them cannot be adjusted at all. Knowing which is which is the whole job.

Width Is the Changeover Nobody Budgets For

Thickness is the variable everyone tracks. It changes the straightener gap, the penetration, the roll pressure and the die shut height, so it gets a setup sheet and a first-piece approval.

Width is treated as a handling question. Move the guide, run a strip, look at it, go. That works while the width stays above roughly 60 percent of the roll face.

Below that, the strip is running on a part of the roll that was never designed for it. Roll deflection is highest at the centre, and a narrow strip sits exactly there.

Width changes also arrive with less warning than thickness changes. A customer trims a part, a service centre ships the next size down, and the schedule quietly moves from 1,200 mm to 600 mm over three weeks.

Nobody calls that a changeover, so nobody re-sets anything. The line keeps running, the parts keep passing, and the flatness complaint arrives two months later with no obvious cause.

Coil width changeover on a 3-in-1 straightener feeder

The Six Settings That Actually Move

Walk the machine from the coil end forward and the list is shorter than most setup sheets suggest.

  • Coil centring on the mandrel, because a 420 mm coil can sit anywhere on a 1,300 mm face and usually does.
  • Entry edge guide opening and its position relative to the line centreline.
  • Side guide clearance, which wants to be 0.5 to 1 mm total rather than proportional to width.
  • Feed roll pressure, since total force should fall with contact area but cylinder pressure is what the gauge reads.
  • Loop sensor or dancer position, which is often mounted where a narrow strip no longer reaches.
  • Die entry guides and pilot clearance, which belong to the tool rather than the machine but get blamed on it.

Six items, twenty-five minutes with a check sheet, and no hardware change. What cannot be changed is the roll crown, which is ground for a design width and stays that way.

What Each Setting Does to the First Hundred Parts

The table links each change to the defect it produces when it is left alone. Read the third column as the cost of skipping that line of the setup sheet.

SettingWhat changes with a narrower coilWhere it costs you
Coil centringCoil can sit off centre by up to 40 mm on a wide mandrelStrip runs diagonally, the edge guide fights it, and the die sees a side load all shift
Edge guide openingOpening has to close by the full width differenceToo tight buckles the edge; too loose lets the strip drift 0.3 mm and clip a pilot
Side guide clearanceAbsolute clearance matters more than relative clearance0.2 mm on a 420 mm strip is a different machine behaviour from 0.2 mm on 1,200 mm
Feed roll pressureContact area falls by up to two thirdsSame cylinder pressure on a third of the area marks the strip and distorts the edge
Loop sensor positionArm may not touch a narrow strip at allLoop control falls back to a timer, and feed length drifts with coil weight
Roll crownNothing moves, and that is the problemA crown ground for 1,200 mm leaves the middle of a 420 mm strip over-rolled

Where Width Bites: Edge Guide and Roll Crown

Two of the six items produce most of the trouble, and they fail in opposite directions.

The edge guide fails visibly. A guide set 1 mm too wide lets the strip wander, and the wander shows up as a pilot mark within fifty strokes.

A guide set too tight bows the strip upward between the guide and the first roll, and the bow becomes a flatness defect.

The working number is 0.4 mm total clearance per side on strip below 500 mm, and 0.8 mm per side above it. Spring-loaded guides tolerate less than roller guides because they follow the strip rather than restrain it.

The roll crown fails quietly. Crown exists to compensate for roll deflection under load, and it is ground for a design width at a design load.

Run a third of that width and the middle of the roll still deflects while the ends carry nothing.

The result is a strip that measures flat on a surface plate and springs into a longitudinal bow after the die. Operators then add penetration, which over-rolls the edges and produces edge wave instead.

Any NC straightener feeder with a fixed crown has this limit. The honest answer on narrow work is a cassette head or a dedicated roll set, not more penetration.

There is a quick way to confirm crown mismatch before ordering anything. Cut three samples across the coil width, lay each on a surface plate, and check the bow direction.

If all three bow the same way, the cause is penetration or the roll stack. If the centre sample bows and the two edge samples do not, the crown is over-rolling the middle and no adjustment will fix it.

Narrow coil entering a 3-in-1 decoiler straightener feeder

How to Prove the First Piece

Six checks, in this order, before the line goes to production speed. The sequence matters because each check invalidates the one before it if it fails.

CheckHow to measure itWhat a failure tells you
Lateral positionStrip edge against the die centreline, dial gauge, three points along the first metreGuide setting or coil centring, not the die
WidthMicrometer at three stations, because slitting tolerance varies along the coilIncoming material, so stop before blaming the line
CamberStraight edge over 1 m of free strip on a flat benchSlitting, which no straightener setting will remove
FlatnessI-units on a surface plate after the rolls, not beforePenetration or crown, and crown cannot be adjusted
Feed lengthDial check on strokes 1 to 5, then every fiftiethRoll pressure or loop control, in that order
Edge conditionVisual and a fingernail test on both edgesGuide clearance too tight, or a burr from slitting

Run the six checks on the first piece of every width change for a month. After that the sheet becomes a habit and the checks take six minutes.

What a Width Change Cannot Recover

Four defects survive a perfect width changeover, and quoting a job without recognising them is how a line gets blamed for a slitting problem.

Camber from slitting. A curved strip stays curved through the rolls. The straightener can reduce it slightly by differential penetration, but the correction is partial and it costs flatness elsewhere.

Edge wave from the slitter. If the coil arrives with a wavy edge, a 3-in-1 decoiler straightener feeder will roll it flatter and then watch it return. Edge wave needs tension, which is a different machine function.

Narrow strip below about 100 mm. The rolls no longer have enough support across the face, and the strip can rotate in the roll gap. Below that width the answer is a dedicated cassette, not a setting.

Crown mismatch on a wide machine. A 1,300 mm roll set running 420 mm strip will always over-roll the middle. If that width is a permanent part of the schedule, the roll set is the wrong size for the work.

The flatness arithmetic behind crown and penetration is covered in full inside the flatness pillar, which is the right place to check a specification before ordering a second roll set.

How long should a width change take on a 1,300 mm machine?

Twenty to twenty-five minutes with a check sheet, against six to eight minutes for a straight coil swap. The extra time is guide setting and the six first-piece checks.

At what width does roll crown start to matter?

Below about 60 percent of the roll face, so under 780 mm on a 1,300 mm machine. Under 40 percent, which is 520 mm, we expect flatness to move by 2 to 4 I-units unless a cassette is used.

How much edge guide clearance should a 420 mm strip have?

0.4 mm per side with roller guides and 0.2 mm with spring-loaded guides. Above 1 mm total the strip will wander enough to clip a pilot within a shift.

Does a width change affect feed length on a 3-in-1 machine?

Only through roll pressure and loop sensing. If both are re-set, feed length should hold 0.05 mm at 200 SPM on any width above 150 mm.

A 3-in-1 decoiler straightener feeder holds flatness only inside the window its roll stack was built for, and that window is defined by width as much as by gauge.

Cassette and roll face options for each model sit in the equipment specification index.

Where to go next

Width is one of four variables that move flatness on the same machine. The flatness pillar sets out the other three and shows which combinations a standard roll stack can still hold.

Read the flatness specification guide

Follow us to Get Latest Updates

subscription